Random Number Generator

This is Midfi Electronics “Random Number Generator”. It’s a radical fuzz that adds oscillation notes that randomly arpeggiate off of the fundamental note played. Crazy noise maker pedal. I’ve built several of these now by request. The owner of the design over at Midfi was gracious enough to share the schematic on the DIYstompboxes forum which is why I want to make it clear that this is NOT my design, and if you get one for me you are strictly paying me to make a clone since these aren’t available anymore.


This is the first one of these I’ve built. I added the mods of changing a 100k resistor with a pot, and a diode that is switched into the circuit, but quite frankly they don’t do a whole lot. Any others of these I build will just have the volume knob as original intended.

Uglyface

The Uglyface effect is an oscillation based distortion/fuzz pedal with envelope controller designed by Tim Escobedo. It can do a wide varitey of off the wall sounds (laser guns, bagpipes, drones), and it has many different ways to modify the circuit. I’ll liked it so much I built it into one of my old junker guitars (details below).


This is the first Uglyface I’ve built. I built it into some crazy electronics box with huge heatsyncs on the sides. Seemed to fit the circuit some how lol. I did the standard controls of Volume, Threshold, Frequency, and Sensitivity, and added a mix control that worked ok.


I had this old guitar knocking around for a while, so I decided to mount an Uglyface inside of it. It has all the same controls as the pedal above, but I also added a Light Sensor with switch for controlling the frequency knob.

Instruments

Over the past few years I’ve built a wide variety of instruments. Some are toys/keyboards/whatever that I re-purposed through circuit bending and modification, some are oscillator based instruments that I built from scratch, and more and more I’ve been dabbling in make effects pedals. I’ve built more things then I could ever possibly list here, but I will try and cover some of the more interesting things. If you want a better idea of what all I’ve done you can got to my Soundclick page. I also have a Youtube Page where you can “see” my instruments in action.

I have two effects pedals that I regularly build. One is the “Mutator” which is a heavily modified toy voice changer re-purposed for guitar/whatever. See those here. The other is a modified Fab Echo. I take this rather tame Echo pedal, and modify it into a fully function delay with lots of features. See those here. I’ve also tried my hand at making more traditional pedals, which you can see here.

Keyboards
I’ve modified lots of keyboards, mostly lower end Casios and Yamahas, but also some toy keyboards as well. The mods have been anywhere from a simple pitch control or glitch push button, all the way to an out board RCA patch (Modular Synth Style) with hundreds of possibilites.

Casio SK-1
One of the holy grails of bending. Most benders want one, have done one, or have done many. The first few a did were based on the “Tablebeast” mods (16 point patch bay with on/off switches). Now that I have some experience with them I’ve undertaken some more complex mods.


This is the first SK-1 I’ve modified. It has the “Tablebeast” Patch bay setup with Pitch Knob, Drum Kill, and Poly Kill Switches. This SK-1 is sold


This SK-1 has pretty much the same mods as the above one, but with the addition of body contacts. This SK-1 is sold.


This just the patchbay for my “Glitchstation” SK-1. The keyboard itself only had a 25 pin connector, pitch knob+body contact, drum kill switch, and 1/4 inch output. The patchbay itself contained all the controls. Housed in an old PS2 case (hence the name) it contained a 26 point patchbay (2 points to ground), 8 point switching patchbay, 3 knobs of different values, and sample and hold section, 3 momentary joystics, and an LFO that can be patched with everything else. This project was complicated and difficult, I don’t know if I would ever take it on again. This keyboard/monster has been sold.

Yamaha VSS-30

By far one of my favorite bends. This sampling keyboard does great on it’s own, but with the addition of some bends becomes a sample crushing machine. See my tutorial for pics, and of course how to make your own. If you have one you would like me to modify just send me a line through the contact page